Open string buzz on delivery...please... Log Out | Topics | Search
Moderators | Register | Edit Profile

Alembic Club » Alembic Basses & Guitars » Open string buzz on delivery...please help! « Previous Next »

Author Message
rob
New
Username: rob

Post Number: 9
Registered: 12-2003
Posted on Thursday, May 27, 2004 - 7:35 am:   Edit Post

Hello all

Well, I just received my 36" scale 5 string Series I w/SII electronics, so I am a very happy man right now (for a pic, see "Rob's Custom Series II" in the FTC section). It's quite amazing, but I am having open string buzz on the A and D strings. Can someone who knows what they're talking about let me know if this sounds like a nut adjustment or a neck adjustment? (I'm new to this adjustable nut thing) If neck, would it be both truss rods since it's the middle two strings?

Thanks for any info!
Rob
effclef
Intermediate Member
Username: effclef

Post Number: 173
Registered: 1-2004
Posted on Thursday, May 27, 2004 - 8:15 am:   Edit Post

Hi, Rob! Fear not...several people will jump in on this. I'll take a first shot: open string buzz is usually at the first fret, which means NUT.

Fret all the strings at the first fret and see if the buzz goes away.

If it does, you may want to raise the nut a little. Loosen the center screw (which fastens it down) and then raise it with the two outside ones. The Alembic "owner's manual" page has info:
Good luck - EffClef.

http://www.alembic.com/support/care.html

"Brass Adjustable Nut

Our unique brass adjustable nut is featured on
every Alembic guitar and bass. There are three
adjustment screws on the string nut. The center
screw locks the nut in place and must be loosened
before attempting to raise or lower the nut. The
two outer screws determine the height of the nut.

The 5/64" hex driver supplied with your
instrument is required to make these adjustments.

Here's how to do it properly:

Detune the bass a little bit.

Loosen the center locking screw.

Adjust the outer screws to the desired height.
When you tighten one of the screws, the height
increases on that side only.

Tighten the center screw once the optimum height
is achieved.

You will need to change the string nut height
when you change the gauge of your strings.

Smaller gauge strings will rest lower in the nut
slots than larger ones. If you dramatically
change the strings, you may need to order a new
nut than can be slotted to your new string size.

You also need to raise the nut if you have a
persistent buzz on open strings.

The nut does not need to be adjusted equally on
both sides. You may want the nut to slant in
certain situations. For cleaning, see the brass
care section of this document."
keavin
Advanced Member
Username: keavin

Post Number: 400
Registered: 12-2002
Posted on Thursday, May 27, 2004 - 8:18 am:   Edit Post

you might want to adjust height on the nut & maybe raise the bridge.
xlrogue6
Member
Username: xlrogue6

Post Number: 67
Registered: 8-2002
Posted on Thursday, May 27, 2004 - 8:25 am:   Edit Post

I'd check the truss rod first--don't know where you're located but most likely source of the problem is that the neck moved in response to differing atmospheric conditions between the Mothership and your place.
bob
Advanced Member
Username: bob

Post Number: 229
Registered: 11-2002
Posted on Thursday, May 27, 2004 - 10:32 am:   Edit Post

Two questions: is it really only the open A and D (no fretted notes), and are you sure it's string buzz and not some other noise?

I agree that the most likely shift in transit would be the neck, but I'd hold off on messing with either the truss rods or bridge until you're sure it's not something simpler. (These aren't difficult, but it's good to take things slowly, one step at a time.)

It seems a little odd that your neck would have straightened just barely enough to give you open string buzz but none on any fretted notes. So raising the nut slightly, mostly on the G side, would be a great place to start.

Also be sure to snug up the lockdown screw (center) when you're done, and check the two outer screws to make sure neither is loose - they're not likely to rattle in a way you would confuse with fret buzz, but you never know. Often a new bass ships with the nut all the way down (so it doesn't look broken to the uninitiated), so the outer screws might not actually be holding up the nut - in which case you should still snug them up so they aren't loose.

If that doesn't work, let us know, and provide any further observations you might have. Good luck, and enjoy.
davehouck
Senior Member
Username: davehouck

Post Number: 594
Registered: 5-2002
Posted on Saturday, May 29, 2004 - 5:48 am:   Edit Post

Hi Rob; congrats on an absolutely wonderful bass!

Topics | Last Day | Last Week | Tree View | Search | Help/Instructions | Program Credits Administration