Q switch instructions

Log Out | Topics | Search Moderators | Register | Edit Profile

Author Message mgirouard3 Junior Username: mgirouard3 Post Number: 14 Registered: 5-2004 Posted on Friday, October 29, 2004 - 4:34 pm:    Are the instructions for the Q switch installation somewhere on this site? My switch arrived today but did not have instructions. mica Moderator Username: mica Post Number: 2046 Registered: 6-2000 Posted on Friday, October 29, 2004 - 4:57 pm:    Sorry about that - here's a PDF of what you should have received: 025-001 025-001.pdf (497.2 k) These instructions predate the prewired kit you received, so you'll be doing steps 1 and 4 and 5 only. hollis Senior Member Username: hollis Post Number: 486 Registered: 11-2003 Posted on Friday, October 29, 2004 - 6:50 pm:    Hi Mica, It was sure nice talking with you and your Mom this afternoon. I think these instructions will work for the three way switch as well, yes? Thanks, Hollis mgirouard3 Junior Username: mgirouard3 Post Number: 15 Registered: 5-2004 Posted on Friday, October 29, 2004 - 8:24 pm:    Thanks Mica, I'll let you know how it works out. mgirouard3 Junior Username: mgirouard3 Post Number: 16 Registered: 5-2004 Posted on Friday, October 29, 2004 - 9:16 pm:    Hello Mica, I was looking at the switch and on the diagram it has a lock washer. The actual switch does not have a typical lock washer from what I have used in the past. Instead there is a smooth black "washer" that is fixed to the threaded part right at the base. Is this the lock washer? mgirouard3 Junior Username: mgirouard3 Post Number: 17 Registered: 5-2004 Posted on Saturday, October 30, 2004 - 5:04 pm:    Hello Mica, Max here again, I decided to install the switch without the lock washer. My worst nightmare came true when as I was drilling, the top of my bass got chipped. After freaking out a little I put the dress washer on and this covered up the chip. Whewwww!!! After installing it, the switch seemed secure so I don't think I will need the lock washwer. But when I plugged it in, and turned the switch on, paddle to the floor, the switch was actualy off. When I positioned the paddle away from the floor it was on. I rechecked my wiring and that is when I noticed that the switch is wired differently that it shows on the diagram. Lets call the insulated wire on terminal one. On the diagram, the capacitor leg is on terminal two, but on my switch it is on terminal three. Is this OK? If the only difference is that my on/off will be reversed I don't care but if it could ruin the electronics I will want to change it. What do you think? mgirouard3 Junior Username: mgirouard3 Post Number: 18 Registered: 5-2004 Posted on Monday, November 01, 2004 - 12:17 pm:    Has anyone else encountered this problem? mica Moderator Username: mica Post Number: 2049 Registered: 6-2000 Posted on Monday, November 01, 2004 - 6:43 pm:    You might want to tack down the chipped finish area with a spot of superglue. It actually doesn't matter which terminal the cap is on, so don't sweat it. The on/off direction has only to with the orientation when you mount it. You're fine just the way you are mgirouard3 Junior Username: mgirouard3 Post Number: 19 Registered: 5-2004 Posted on Monday, November 01, 2004 - 9:35 pm:    Thanks! The sound of my bass with the Q off is exactly the sound I was looking for. I have a Hartke 2.5xl and no matter how I adjusted the EQ, it was too "glassy". The Q switch on will be for when I do my solo spot. Thanks again.