String Gauge ? Log Out | Topics | Search
Moderators | Register | Edit Profile

Alembic Club » Alembic Basses & Guitars » Archive 2006 » Archive through August 29, 2006 » String Gauge ? « Previous Next »

Author Message
brianm
Junior
Username: brianm

Post Number: 36
Registered: 8-2005
Posted on Thursday, August 03, 2006 - 10:45 am:   Edit Post

I'm currently using GHS bass boomers, (round wound) light gauge (40, 55, 75, 95) on a 4 string medium scale bass. I just purchased a used short scale series I (4 string) and I'd like to go with even lighter string gauges. I've wondered about buying a 6 string set and substituting the A string for an E string, D string for the A string, etc. Any one tried this? I was wondering if any one has any suggestions or recommendations?
crgaston
Advanced Member
Username: crgaston

Post Number: 236
Registered: 11-2005
Posted on Thursday, August 03, 2006 - 10:55 am:   Edit Post

www.juststrings.com sells single strings, which might be cheaper than buying six and throwing away two.
lidon2001
Intermediate Member
Username: lidon2001

Post Number: 197
Registered: 4-2005
Posted on Thursday, August 03, 2006 - 11:12 am:   Edit Post

Check out Rotosound Funkmaster. 30-50-70-90.

T
olieoliver
Senior Member
Username: olieoliver

Post Number: 601
Registered: 2-2006
Posted on Thursday, August 03, 2006 - 12:18 pm:   Edit Post

That light of gauge strings may cause problems with keepimg the neck straight. You may have to adjust the truss rods more often. I like the feel of light gauge strings but the sound of the heavier strings IMHO is much better.
eligilam
Junior
Username: eligilam

Post Number: 20
Registered: 2-2006
Posted on Thursday, August 03, 2006 - 1:53 pm:   Edit Post

I play a Stanley Signature (short scale) with Roto Funkmasters, and have all the joy of that rubber-bandy, chord-strumming thing that goes along with them...no neck problems yet.

I did have piccolo strings on there (from juststrings.com, by the way---great site), but they cut like barbed-wire into my fingers. Also, the mass of those strings was too light for good slapping. (Although, for bad slapping, any gauge will work.)

W.D.
brianm
Junior
Username: brianm

Post Number: 37
Registered: 8-2005
Posted on Thursday, August 03, 2006 - 4:31 pm:   Edit Post

Thank you every one! I checked out www.juststrings.com and the Rotosound Funkmaster strings are long scale. Since this is my first experience with a short scale, do you think it would cause any problems using long scale strings on a short scale bass other than having the bare metal part of the strings wrap around the tuning pegs?

Thanks for tip on the piccolo strings, I was also considering them for a different bass I own.
crgaston
Advanced Member
Username: crgaston

Post Number: 237
Registered: 11-2005
Posted on Thursday, August 03, 2006 - 8:56 pm:   Edit Post

Well, some will tell you never to cut your strings, but I've never had problems. On the other hand, I've never cut them to fit a short scale, either.
lidon2001
Intermediate Member
Username: lidon2001

Post Number: 198
Registered: 4-2005
Posted on Thursday, August 03, 2006 - 9:19 pm:   Edit Post

I trim the cloth covered area a few inches and have had no problems with the metal on the peg since I've had my short scale.
dfung60
Intermediate Member
Username: dfung60

Post Number: 192
Registered: 5-2002
Posted on Thursday, August 03, 2006 - 10:52 pm:   Edit Post

I think you really want to try to look a little more for short scale strings. The problem that you can run into is that you don't want the outer wrapped layer to curl around the tuning head. If you do that, there's a good chance that that winding will unwrap as you come up to pitch, ruining the string. You have to be especially careful about this with the low E and high G since, on a short scale bass, those pegs are closer to the bridge than the nut would be a on a long scale.

Some strings won't have a problem with unraveling, but certainly the stiff ones (like a Fender flatwound) will fail.

Topics | Last Day | Last Week | Tree View | Search | Help/Instructions | Program Credits Administration