Double truss rod alignment Log Out | Topics | Search
Moderators | Register | Edit Profile

Alembic Club » Alembic Basses & Guitars » Archive: 2007 » Archive through July 18, 2007 » Double truss rod alignment « Previous Next »

Author Message
grooveman
Junior
Username: grooveman

Post Number: 23
Registered: 6-2007
Posted on Wednesday, July 04, 2007 - 2:34 am:   Edit Post

Hi everybody, I have a question:

I suppose this subject is not new but ...

Sinds I've replaced strings with thinner one's, I have a little bow in my neck wich I have to correct ... What is the best/smartest way to align the double truss rod(s) on my spoiler? Is there a specific sequence/order to do this? I'm feel a little uncomfortable to get a neck-twist between the E- and G-string ...

This is the first bass I have with a double truss rod ... the rest of adjustment like 'bridge' and 'intonation' is not new for me so this isn't a problem!

Thanks for help!
Andy
adriaan
Senior Member
Username: adriaan

Post Number: 1539
Registered: 6-2002
Posted on Wednesday, July 04, 2007 - 2:48 am:   Edit Post

Go easy - not more than 1/4 turn at a time, and always adjust both rods. Let the bass settle in with the new setting.

If you're making a big adjustment, wait until the next day before deciding to adjust again.

Did you find Joey's famous post on setting up your instrument? Check out the "Must Reads" section from the main page of the club.
terryc
Intermediate Member
Username: terryc

Post Number: 196
Registered: 11-2004
Posted on Wednesday, July 04, 2007 - 6:00 am:   Edit Post

Grooveman, I strongly recommend the set up in the 'Must read' section, I have discussed maintaining your instruments in a thread called 'The Knowledge'. Even though I knew about set up I found that thread very informative and should be taken seriously if you want a great playing bass and no damage afterwards. I said in my post that you get a wrecked guitar/bass and experiment on that to get the general 'ways & means' of truss rod adjustment but Alembics are truly the most adjustable basses in the world and have been copied by other makers.
Just as adriaan says..go easy and be patient.
adriaan
Senior Member
Username: adriaan

Post Number: 1541
Registered: 6-2002
Posted on Wednesday, July 04, 2007 - 6:12 am:   Edit Post

By the way, Andy - you're in the Netherlands, right? Make sure you use a proper 1/4 inch wrench, because millimeter sized tools will damage the nuts and bolts!

If you can't find a 1/4" wrench, contact Edwin at the Bass Connection in Hilversum.
grooveman
Junior
Username: grooveman

Post Number: 24
Registered: 6-2007
Posted on Wednesday, July 04, 2007 - 6:30 am:   Edit Post

OK my friends, I've found it!

That's a lot of info about this subject ... Great!! But it still stays a little spooky to start with! I didn't know you could make a unrepairable 'twisted banana' of your bass! I'll be carefull and patient as much as possible!

The 1/4"-wrench isn't a problem! We have a very good hardware-store here in Nijmegen!

Andy
grooveman
Junior
Username: grooveman

Post Number: 30
Registered: 6-2007
Posted on Friday, July 06, 2007 - 11:57 pm:   Edit Post

Done!!

7-7-07 Straight again!
Easy as it is! Case closed!

Thanks for help!
davehouck
Moderator
Username: davehouck

Post Number: 5254
Registered: 5-2002
Posted on Saturday, July 07, 2007 - 8:11 am:   Edit Post

Congrats!

Topics | Last Day | Last Week | Tree View | Search | Help/Instructions | Program Credits Administration