Alembic Further, control cavities/bat... Log Out | Topics | Search
Moderators | Register | Edit Profile

Alembic Club » Owning an Alembic » Troubleshooting » Archive through February 17, 2014 » Alembic Further, control cavities/battery questions « Previous Next »

Author Message
charley
Junior
Username: charley

Post Number: 24
Registered: 8-2005
Posted on Tuesday, February 26, 2013 - 5:30 am:   Edit Post

I have a Further with LEDs. There are 3 control cavities on back. The first (largest) allows access to all the pots and switches.

1. The second (middle size) rear cavity has 4 9V batteries. What do these control?

2. The smallest cavity fits 1 9V battery. What does this control?

3. The LED switch on the front is "off" in the "up position." The fx loop control on the front is also an on/off switch. I assume that the "up position" is "off" as well? When the switch is "up" the output volume is extremely low and thin sounding. In the "down" position the volume is loud and the signal so strong it overdrives whatever it is plugged into? IS this normal. I only run my guitar in mono.

5.
keith_h
Senior Member
Username: keith_h

Post Number: 1848
Registered: 2-2005
Posted on Tuesday, February 26, 2013 - 7:05 am:   Edit Post

Charley,
1. This is for the LED's in the neck.
2. This is for the preamp.
3. I can't answer and will let others who have
Furthers.

Keith
charley
Junior
Username: charley

Post Number: 25
Registered: 8-2005
Posted on Tuesday, February 26, 2013 - 7:12 am:   Edit Post

I only had 4 9V batteries around and chose to replace the 4 battery LED cavity, thinking that I was replacing the preamp batteries (not believing that there was any way those little lights could use that many batteries).

Looks like that most likely explains why the guitar is so quiet. Will try replacing the last 9V and see......

Thanks!
lbpesq
Senior Member
Username: lbpesq

Post Number: 5356
Registered: 7-2004
Posted on Tuesday, February 26, 2013 - 7:50 am:   Edit Post

Charley:

When you flipped the OBEL (on-board effects loop) control and got little sound, did you have any effects plugged into the OBEL stereo jack at the time?

Bill, tgo
charley
Junior
Username: charley

Post Number: 26
Registered: 8-2005
Posted on Tuesday, February 26, 2013 - 8:14 am:   Edit Post

I'm assuming that "up" is the off position for that switch. That being the case, I get only very quiet sounds in the "off" position, and very loud overdriven sounds in the "on" position.

My guitar is routed from Further Mono Out > pedalboard > amp.
charley
Junior
Username: charley

Post Number: 27
Registered: 8-2005
Posted on Tuesday, February 26, 2013 - 8:16 am:   Edit Post

Can anybody confirm the fx loop switch to be "up/off" and "down/on?"
adriaan
Moderator
Username: adriaan

Post Number: 3022
Registered: 6-2002
Posted on Tuesday, February 26, 2013 - 8:29 am:   Edit Post

Well, there's always the FAQ page for Further and Tribute.
charley
Junior
Username: charley

Post Number: 28
Registered: 8-2005
Posted on Tuesday, February 26, 2013 - 9:06 am:   Edit Post

No info on position, just switch location on the FAQ.
lbpesq
Senior Member
Username: lbpesq

Post Number: 5357
Registered: 7-2004
Posted on Tuesday, February 26, 2013 - 10:01 am:   Edit Post

Charley:

The OBEL switch switches the effects loop in and out of the signal chain. When the OBEL is switched on, and there is nothing plugged into the OBEL stereo jack, you should get little, if any, signal getting through. If you're running the guitar out to the effects, then to the amp, you're not using the OBEL. In this situation, one position of the OBEL switch should give you full signal, the other little or no signal. If you are getting full signal in one of the positions, then your battery has some juice in it. If the pre-amp battery is dead, you shouldn't get any signal. As for up vs. down, I'm not sure off the top of my head, but if I can get to my instruments later today, I'll check.

Bill, tgo
mica
Moderator
Username: mica

Post Number: 7932
Registered: 6-2000
Posted on Tuesday, February 26, 2013 - 12:20 pm:   Edit Post

The usual way for us to orient switches is down (toward the floor) is on while you are playing the guitar.
charley
Junior
Username: charley

Post Number: 29
Registered: 8-2005
Posted on Thursday, February 28, 2013 - 6:57 am:   Edit Post

Okay, popped a new 9V in and everything sounds great!

The switches are all giving me problems. I have exercised them all, and not much has resulted. Most of them have to be switched on, then sort of pushed to one side to get them to work. Any next steps I should try to get them to work better?
jazzyvee
Senior Member
Username: jazzyvee

Post Number: 3351
Registered: 6-2002
Posted on Thursday, February 28, 2013 - 11:36 pm:   Edit Post

have that switch problem you mention with my black Europa/Elan for the switch that works the LED's. To get them on I have to push the switch down and push side to side before they stay on. All the other switches are fine.

Jazzyvee
lbpesq
Senior Member
Username: lbpesq

Post Number: 5359
Registered: 7-2004
Posted on Friday, March 01, 2013 - 12:08 am:   Edit Post

My Further is back at the Mothership for this same problem with my LED mini toggle. Mica says they just don't make them like they used to.

Bill, tgo
lidon2001
Senior Member
Username: lidon2001

Post Number: 504
Registered: 4-2005
Posted on Monday, March 04, 2013 - 8:41 am:   Edit Post

Same LED switch issue here, even after a switch change.

How about an on/off switch like the midi channel changer on the current COTM? It would be sleek and out of the way.

Topics | Last Day | Last Week | Tree View | Search | Help/Instructions | Program Credits Administration