P-bass jack connector Log Out | Topics | Search
Moderators | Register | Edit Profile

Alembic Club » Owning an Alembic » Troubleshooting » P-bass jack connector « Previous Next »

Author Message
carsbybigd
New
Username: carsbybigd

Post Number: 1
Registered: 8-2014
Posted on Wednesday, August 13, 2014 - 4:15 pm:   Edit Post

I just purchased a Alembic P-bass set.As I was installing it,I noticed a purple wire had come loose from the black square assembly below the 1/4" jack.It looks like there are 2 possible places it went to.Need help figuring out where it goes.Also,where does the ground from the bridge connect to also ? Thanks for your help.
mica
Moderator
Username: mica

Post Number: 8229
Registered: 6-2000
Posted on Wednesday, August 13, 2014 - 5:00 pm:   Edit Post

No bridge ground - the system is grounded when the shielding of the cavity contacts the rivets that holds the pots together, it's automatic.

L113
carsbybigd
New
Username: carsbybigd

Post Number: 2
Registered: 8-2014
Posted on Wednesday, August 13, 2014 - 5:08 pm:   Edit Post

Thanks Mica,John Prock said to give you a call but that solved it.
carsbybigd
New
Username: carsbybigd

Post Number: 3
Registered: 8-2014
Posted on Monday, August 18, 2014 - 3:32 pm:   Edit Post

I got it installed,everything works ,but I have a bad hum when I go past halfway on the tone/treble.The bass part of the tone sounds great[DEEP and FULL] but the hum is awful.Any ideas ?
mica
Moderator
Username: mica

Post Number: 8235
Registered: 6-2000
Posted on Monday, August 18, 2014 - 4:18 pm:   Edit Post

Is the pickup plugged in correctly? There is a friction lock that should engage a little retainer on the board.

Also, did you shield the cavity and the underside of the pickguard? Can you post a picture of the installation? Do you have 2 or 3 controls?

Also, is the sounds you're hearing a low-frequency hum (like 60Hz)or is the noise higher frequency?
carsbybigd
New
Username: carsbybigd

Post Number: 4
Registered: 8-2014
Posted on Monday, August 18, 2014 - 5:07 pm:   Edit Post

I'll check tomorrow and take some pictures.2 controls 1 volume and 1 tone/pan[sweep?] and the jack.
carsbybigd
New
Username: carsbybigd

Post Number: 5
Registered: 8-2014
Posted on Friday, August 22, 2014 - 11:01 pm:   Edit Post

Ok ,shielded the cavity[see pics],put it all back together and nothing. Noticed another wire had come off,the red from the battery to the 1/4" jack.Checked out the schematic you provided and noticed that the 2 black wires were not soldered together.Moved them over [together] and soldered the red where it shows in your photo.Nothing. no sound no nothing.The friction lock[with 3 wires red,yellow and black] is kinda loose,but does make a connection.The hum I was hearing was kinda high[ I only noticed it when turning the tone from deep bass to treble...on the treble side]. Here's the pics
carsbybigd
New
Username: carsbybigd

Post Number: 6
Registered: 8-2014
Posted on Friday, August 22, 2014 - 11:13 pm:   Edit Post

jack
carsbybigd
New
Username: carsbybigd

Post Number: 7
Registered: 8-2014
Posted on Friday, August 22, 2014 - 11:18 pm:   Edit Post

jack 2
carsbybigd
New
Username: carsbybigd

Post Number: 8
Registered: 8-2014
Posted on Friday, August 22, 2014 - 11:20 pm:   Edit Post

cavity
carsbybigd
New
Username: carsbybigd

Post Number: 9
Registered: 8-2014
Posted on Friday, August 22, 2014 - 11:24 pm:   Edit Post

tone
carsbybigd
New
Username: carsbybigd

Post Number: 10
Registered: 8-2014
Posted on Friday, August 22, 2014 - 11:29 pm:   Edit Post

tone and jack
carsbybigd
Junior
Username: carsbybigd

Post Number: 11
Registered: 8-2014
Posted on Friday, August 22, 2014 - 11:35 pm:   Edit Post

In the photo I posted at 11:18 the wires are [from the far right] purple[violet] from volume,red from battery,red and white from volume,black and another that is kinda black/purple.The black/purple is from the volume and the other is from the battery.
mica
Moderator
Username: mica

Post Number: 8246
Registered: 6-2000
Posted on Monday, August 25, 2014 - 12:10 pm:   Edit Post

Make sure that the solder sides of the boards cannot contact the shielded walls of the cavity or it can short out and have no sound. If they are clear, then you might want to unmount the pickups from the shielded area (just lift them out) and see if you can get any signal that way.

Are you saying that the output jack was wired completely differently on the original install? The system you have is over 20 years old, so it may be worth sending in here for testing. There is no charge to test the pickups and electronics (just pay return freight) so at least we can narrow down possibilities.
carsbybigd
Junior
Username: carsbybigd

Post Number: 12
Registered: 8-2014
Posted on Monday, August 25, 2014 - 2:56 pm:   Edit Post

I'll try that 1st otherwise I'll be sending them in.Thanks
carsbybigd
Junior
Username: carsbybigd

Post Number: 13
Registered: 8-2014
Posted on Monday, August 25, 2014 - 5:18 pm:   Edit Post

Is the 45 degree angled corner where the 2 black wires go ?
carsbybigd
Junior
Username: carsbybigd

Post Number: 14
Registered: 8-2014
Posted on Monday, August 25, 2014 - 6:34 pm:   Edit Post

Ok I got it to work ,no hum either.....but,it will only play if the cord is pulled back out about 1/2".Feels like it's just before it engages to lock it in.Here are some pics # 1 is the actual jack and #2 is a piece of paper showing what is what and where it is right now[the copper reflection makes the edge of the plug look ragged it isnt.] So Im guessing I almost have it wired up correctly as I got sound and no hum ! Yea !#1#2
mica
Moderator
Username: mica

Post Number: 8247
Registered: 6-2000
Posted on Monday, August 25, 2014 - 8:20 pm:   Edit Post

Now that I'm looking at it more closely, I don't think you have the correct jack - it looks very similar, but if the 45 degree corner is the lower left corner like in my picture at the top of the thread, the tip should be on the right edge - in yours, it's at the top edge.

You are going to need a new jack. Email me (click on my profile on the left) and we will work out the details.
mica
Moderator
Username: mica

Post Number: 8248
Registered: 6-2000
Posted on Monday, August 25, 2014 - 8:25 pm:   Edit Post

Yours appears to be a 113E, which is a "break" circuit connector, so instead of turning it on, it turned the circuit off. We've never ordered that jack before.

Mystery solved!
carsbybigd
Junior
Username: carsbybigd

Post Number: 15
Registered: 8-2014
Posted on Sunday, August 31, 2014 - 10:57 am:   Edit Post

AHHHHHHH ,nothing like the sweet sounds of an Alembic coming out of my P-Bass.....with NO HUM !!! THANK YOU MICA and Alembic.
davehouck
Moderator
Username: davehouck

Post Number: 11486
Registered: 5-2002
Posted on Sunday, August 31, 2014 - 11:26 am:   Edit Post

:-)
funkyjazzjunky
Senior Member
Username: funkyjazzjunky

Post Number: 921
Registered: 5-2007
Posted on Sunday, August 31, 2014 - 3:43 pm:   Edit Post

I will bet neither Fender's nor Gibson's family assisted a client so well!




VMG
carsbybigd
Junior
Username: carsbybigd

Post Number: 16
Registered: 8-2014
Posted on Thursday, October 30, 2014 - 3:23 pm:   Edit Post

You can say that again Funky. Great experience,and it's just a pickup . When I get my next bass,I will again own an Alembic.

Add Your Message Here
Post:
Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Last Week | Tree View | Search | Help/Instructions | Program Credits Administration