Series I Distortion Log Out | Topics | Search
Moderators | Register | Edit Profile

Alembic Club » Owning an Alembic » Troubleshooting » Series I Distortion « Previous Next »

Author Message
hammer
Senior Member
Username: hammer

Post Number: 858
Registered: 9-2009
Posted on Thursday, February 25, 2016 - 9:38 am:   Edit Post

Over the past 2-3 days I have been experiencing a significant amount of distortion from my new/used Series I. I've checked out my rig with other basses and the sound is as clear as a bell so it's either in the electronics of the Series I or the 5-pin cable I would think (I wouldn't think the DS-5 would be involved but what do I know).

The distortion is more obvious in some frequencies than others, but appears to be there all of the time and is apparent whether playing through either PU.

Any thoughts as to how to track down the source of the problem would be appreciated.
sonicus
Senior Member
Username: sonicus

Post Number: 4783
Registered: 5-2009
Posted on Thursday, February 25, 2016 - 10:29 am:   Edit Post

HI Brian ,
The output of your Series I is higher ( hotter ) then that of other instruments. It is possible that you are overdriving the input stage of your bass rig. If there is a passive / active input selection always use the active input. If you have a pad switch button set it for a minus gain setting. OR , if your rig has a master volume out potentiometer and an input gain potentiometer set the master out higher then the gain input. The key here is to build gain structure conducive to a clean signal to your ears ! It is very possible that your Series I is a healthy critter and just being who she is correctly !

Let me know how that works ,

Wolf
keith_h
Senior Member
Username: keith_h

Post Number: 2374
Registered: 2-2005
Posted on Thursday, February 25, 2016 - 10:43 am:   Edit Post

Have you tried exercising the pots and switches?

If you use the battery through the 1/4 inch jack do you get the same results? If not it could indicate a bad 5-pin cable or less likely something in the DS-5. I have had some noise from my DS-5R where I needed to exercise the stereo/mono switch since I never use it. If nothing changes then you can be pretty sure it is internal to the bass.

I would also open her up and reseat the connectors on the board in case one came loose.

Keith
stephenr
Intermediate Member
Username: stephenr

Post Number: 178
Registered: 9-2014
Posted on Thursday, February 25, 2016 - 10:57 am:   Edit Post

Also think you should check the amount of gain set on the pickups themselves. The Series electronics can be set up with enough gain to drive a power amp without using a preamp. If the pickup gain is too hot it it is probably causing the input of your preamp to clip. Try setting the gain to the lowest setting and see if the distortion goes away.
hammer
Senior Member
Username: hammer

Post Number: 859
Registered: 9-2009
Posted on Thursday, February 25, 2016 - 12:04 pm:   Edit Post

I'm going to get some batteries and try it through the 1/4 inch jack tonight and will also exercise the stereo mono switch. Right now its about the only switch, knob, jack I've missed.

My rig is composed of 2 F1-Xs and an SF-2 powered by a Yamaha P5000. I'll look in to the gain setting but with the current set-up would not think that's a problem unless it's with the PUs (which are relatively new versions installed by a previous owner). I'll check in to that tonight.
sonicus
Senior Member
Username: sonicus

Post Number: 4784
Registered: 5-2009
Posted on Thursday, February 25, 2016 - 12:30 pm:   Edit Post

( double post correction)

(Message edited by sonicus on February 25, 2016)
sonicus
Senior Member
Username: sonicus

Post Number: 4785
Registered: 5-2009
Posted on Thursday, February 25, 2016 - 12:32 pm:   Edit Post

Brian,
Try just the two F1-X preamps to the power-amp first and bypass the SF-2 Super Filter before you try anything else. Set the power amps gain higher then the pre-amps gain . See how that sounds. The SF-2 Super Filter can be added again but might have to be dialed in , to the gain structure.

Wolf
hammer
Senior Member
Username: hammer

Post Number: 860
Registered: 9-2009
Posted on Thursday, February 25, 2016 - 12:50 pm:   Edit Post

Sonicus

Will do
lbpesq
Senior Member
Username: lbpesq

Post Number: 6365
Registered: 7-2004
Posted on Thursday, February 25, 2016 - 4:12 pm:   Edit Post

Brian:

I'd suggest you try only one fix at a time. The first thing I would do is try the 1/4" cable before I changed anything else.

Bill, tgo

Add Your Message Here
Post:
Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Last Week | Tree View | Search | Help/Instructions | Program Credits Administration