SVT, B-15 and Series II Log Out | Topics | Search
Moderators | Register | Edit Profile

Alembic Club » Owning an Alembic » Troubleshooting » Archive through March 08, 2009 » SVT, B-15 and Series II « Previous Next »

Author Message
petehnek
Junior
Username: petehnek

Post Number: 28
Registered: 8-2006
Posted on Monday, March 03, 2008 - 6:39 am:   Edit Post

I've got an old SVT and B-15 that I recently had fixed up and I'm trying to get the Series II to play through them. Is there anything special I should do? Just Series II-->DR-5-->Ampeg or does something else get thrown in between the DR-5 and Ampeg? Haven't been able to get it to work right yet for some reason. The B-15 blew up (not sure if it can be related) and the SVT sounded distorted. Whatup with that?
jbybj
Intermediate Member
Username: jbybj

Post Number: 142
Registered: 6-2006
Posted on Monday, March 03, 2008 - 10:19 am:   Edit Post

The "old SVT" was probably designed with a gain stage that expected the lower level input of a passive instrument. If the output of an active electronics instrument is too hot, it will distort right at the input stage. Try turning down the preamps inside your Series II. Good luck, JBY
hieronymous
Advanced Member
Username: hieronymous

Post Number: 264
Registered: 1-2005
Posted on Monday, March 03, 2008 - 2:29 pm:   Edit Post

Also, my impression is that active instruments aren't really meant to be played with the volume at 10 - instead, "10" (on a passive instrument like a Fender Precision Bass) is somewhere in the middle, and you can go above 10 or below.

Did you have the volume pot maxed on your bass?
petehnek
Junior
Username: petehnek

Post Number: 29
Registered: 8-2006
Posted on Monday, March 03, 2008 - 4:57 pm:   Edit Post

I'm not sure where the volume was. I had both pickups on full I'm sure, not sure where I had the master volume. I'll have to check it out.

The SVT is about a 1970 and the B-15 is a 1966. The SVT is sounding awesome with my main Fender Jazz and the B-15 was sounding great until I tried the Alembic out on it, when is suddenly stopped making any noise. It's not a fuse I think cause the tubes are on. Just no sound. Can simply plugging in a Series II do that to an old amp? Seems a bit much.
davehouck
Moderator
Username: davehouck

Post Number: 6289
Registered: 5-2002
Posted on Monday, March 03, 2008 - 8:25 pm:   Edit Post

On the back of a Series bass are four trim pots accessible with a small screw driver through the back plate. The two outside trim pots are the gain adjustments for the pickups. Full clockwise is all the way up; counterclockwise lowers the output. Don't overturn; full travel is about 300°.

Have you determined whether the problem of "no sound" is the amp or the cab?

(Message edited by davehouck on March 04, 2008)
petehnek
Junior
Username: petehnek

Post Number: 30
Registered: 8-2006
Posted on Tuesday, March 04, 2008 - 5:47 am:   Edit Post

Excellent, I'll check out the trim pots, I guess turn them about halfway?

I don't know what the issue is. I just had the thing restored and it was sounding fantastic. Then I plugged in the Alembic and zip. Could be coincidence, maybe something wrong with the wiring that was missed. I don't think the rectifier tube is lighting up.

Topics | Last Day | Last Week | Tree View | Search | Help/Instructions | Program Credits Administration