| Author | Message | ||
| garth4664
Junior Username: garth4664 Post Number: 37 Registered: 10-2008 |
Big problem please help. My neck pickup circuit started making loud intermittant crackling sounds at a gig last night. Fortunately could switch to the bidge and complete the gig.(When I turned down the neck pickup volume or switched the neck pickup off there was no crackling at all and the bass sounded as usual.) I have had a chance to investigate the issue today - it is really strange. Generally speaking if i sit still and "turn" the neck pickup volume adjustment trim pot (on the back of the insrument) the crackling goes away and the neck pickup sounds clear. But if I get too vigourus or tap the back brass cover the crackling can come back (it is not the same result everytime). I opened the back of the bass and noticed that if I tap the components on the circuit (card) I get a crackle with each tap. Swapping the pick ups does not change the issue, I.e. the neck pickup works very fine with the bridge pickup circuit and the bridge pickup crackles through the neck pickup circuit. so the issue seems to be in the circuit (card) rather than the pickups themselves. Mica is this something that I need to send the circuit board back to Alembic's factory to fix? Are there any further tests I could run? Please help, Garth | ||
| slawie
Intermediate Member Username: slawie Post Number: 105 Registered: 8-2002 |
Hey Garth sorry about the problem nothing worse that your Alembic sounding sh!tty. Check connectors that they are seated properly. And also a simple thing is to run an pen eraser (one of the rough ones - not pencil kind) on the pins of the connectors to lightly rough up the metal thereby cleaning the surface. You can get one of those jewellry eye pieces and check for dry or cracked solder joints and or connections. I am an old fart and need one of these. Any of you young folks can probably see it with the naked eye. Look at the points where components or sockets are connected to the PCB (printed circuit board) Look for discloloured or not shiny joints or a blackline around the component solder interface. If you find any of these, solder it/them up, or if you don't trust your soldering skills, find someone who can. Or send it back to Alembic. It might not fix the problem but it's a good place to start. Sorry if I am repeating something you aleady have tried. slawie | ||
| garth4664
Junior Username: garth4664 Post Number: 38 Registered: 10-2008 |
Thanks Slawie, Tried all of the above - nothing out of place on the soldering side, and bass plays perfectly if I remove the PF6 and just let it dangle from the leads in the breeze with the back plate removed. I think it is a faulty component, simply because where there is no vibration there is no noise, but perhaps it is an unobvious solder connection. I've written to Alembic help email asking whether I should send the PF6 through to them. Hopefully it won't take them too long to repair and send back to me  Life without a series 1 is going to be pretty tough. Will have to stay away from tall building windows and sharp objects. Thanks for all the advice. Cheers, Garth | ||
| tdukes
Intermediate Member Username: tdukes Post Number: 164 Registered: 4-2008 |
It took about a week and a day or so for me to get mine there, fixed and back again. My total cost was a little over $50. I guess the cost will depend on what's is wrong with your card and how you ship it. My problem was a FET, sounds like you may have a bad trim pot. Good luck, Todd. | ||
| garth4664
Junior Username: garth4664 Post Number: 39 Registered: 10-2008 |
2-3 weeks after writing the email to Alembic help still no reply. Not sure if I should just send the PF6 card back or not - will Alembic look after it if it arrives unannounced? | ||
| davehouck
Moderator Username: davehouck Post Number: 8816 Registered: 5-2002 |
Try giving Mica a call. Probably the best time would be between 10 and 4 pacific time. | ||
| mica
Moderator Username: mica Post Number: 6405 Registered: 6-2000 |
Garth, I did not see your email. You can send the card in no problem. Make sure you send it in a static-safe bag, then packed in a sturdy BOX (I will actually be mad if it arrives in a padded envelope, and you don't want to see me mad). Include a note with: -your name and return address -phone number/email to contact you about the repair -serial number of your bass -description of the problem you observed -what troubleshooting you attempted first There's a $75 cap on PF-6 card repairs. Shipping is additional. BTW, you should insure the card for $350, since that's the replacement value of a new one. | ||
| garth4664
Junior Username: garth4664 Post Number: 40 Registered: 10-2008 |
Hello Mica, Thanks so much - will send via hong kong express post as instructed. I will also send all the details as requested - will be so good to have the series 1 fixed...can't wait. | ||
| garth4664
Junior Username: garth4664 Post Number: 50 Registered: 10-2008 |
Hello Mica, Any word on this - has the PF6 been repaired yet? Kindest regards, Garth | ||
| mica
Moderator Username: mica Post Number: 6465 Registered: 6-2000 |
I am not in the office today, sorry I missed this message on Monday, but I believe it's complete and ready for return shipment. I'll check on Monday and let you know. (Message edited by mica on November 25, 2009) | ||
| garth4664
Member Username: garth4664 Post Number: 52 Registered: 10-2008 |
Hello Mica, Thanks - please feel free to charge my credit card (details as provided earlier) and send back to my office address. Thanks again for all your help  , can't wait to play the old girl at my next gig. Cheers, Garth | ||
| garth4664
Member Username: garth4664 Post Number: 53 Registered: 10-2008 |
Hello Mica, Thanks - please feel free to charge my credit card (details as provided earlier) and send back to my office address. Thanks again for all your help , can't wait to play the old girl at my next gig. Cheers, Garth | ||
| garth4664
Member Username: garth4664 Post Number: 75 Registered: 10-2008 |
Hello Mica, any word on this? Has it been sent yet? would love to get the 78 coco sounding again... | ||
| garth4664
Member Username: garth4664 Post Number: 79 Registered: 10-2008 |
Mica, I heard from Mary that the Alembelectrictricians couldn't figure out what is wrong with the circuit board - any news?? | ||
| garth4664
Member Username: garth4664 Post Number: 90 Registered: 10-2008 |
Hello Mica, Sent an email - is this ready to be sent back yet? Any news? Cheers, Garth | ||
| garth4664
Member Username: garth4664 Post Number: 91 Registered: 10-2008 |
Any news would be good news? Help? | ||
| garth4664
Intermediate Member Username: garth4664 Post Number: 101 Registered: 10-2008 |
Mica - is anyone there - have sent emails... | ||
| garth4664
Intermediate Member Username: garth4664 Post Number: 113 Registered: 10-2008 |
Still no word on this repair - can someone call Alembic for me or mention it when they chat, I would really like to get my Cocobolo sounding again. Cheers Garth | ||
| mica
Moderator Username: mica Post Number: 6659 Registered: 6-2000 |
Hmm, this was set aside after inconclusive tests and sadly overlooked. Dad is doing some more tests on it (at this moment!) and I hope to have some more details for you in a day or two. Sorry this is taking so long. | ||
| garth4664
Intermediate Member Username: garth4664 Post Number: 114 Registered: 10-2008 |
Thanks Mica, I can see from the site how busy things are there. Just glad to hear that you are on the case. Look forward to hearing the results of the test. | ||
| mica
Moderator Username: mica Post Number: 6660 Registered: 6-2000 |
Found some problems - which is good. But they were a little trixy! Looks totally fixed, just one more string of tests and we'll ship it off. Email me your current shipping address, it's been so long, you may have moved in the meantime. | ||
| garth4664
Intermediate Member Username: garth4664 Post Number: 115 Registered: 10-2008 |
Hello Mica, Actually I have moved countries since then but will get you to send back to my wife's work address in Hong Kong. I will send you the current shipping address in Hong Kong via email. Thanks again and look forward to getting the coco sounding again. Cheers, Garth | ||
| garth4664
Intermediate Member Username: garth4664 Post Number: 118 Registered: 10-2008 |
Hello mica, did you get my email? Is my PF6 being sent back? Thanks | ||
| garth4664
Intermediate Member Username: garth4664 Post Number: 119 Registered: 10-2008 |
Still nothing from you Mica, Susan. Can you please email me at garth4664@gmail.com Has been a long time for this PF6 card. | ||
| mica
Moderator Username: mica Post Number: 6744 Registered: 6-2000 |
How lame is that? The parcel was all perfectly packed, customs form all filled out, and then safely covered by some packing material until today. It's outta here in the am post - I will confirm that the same has happened for you tomorrow. Sorry for the delay. | ||
| garth4664
Intermediate Member Username: garth4664 Post Number: 120 Registered: 10-2008 |
Thanks Mica, really can't wait to put this bass back in service. I miss it badly. | ||
| garth4664
Intermediate Member Username: garth4664 Post Number: 123 Registered: 10-2008 |
Hello Mica, PF-6 back in place and bass sounding great. Thanks for your help, I'm so glad to have this one back in service, it is a great sounding bass with such a clear tone. I think I like the sound slightly more than it's better looking sister, 76AC070. This is the first time I have had the chance to compare them back to back. I'm so happy, thanks again. | ||
| jacko
Senior Member Username: jacko Post Number: 2618 Registered: 10-2002 |
I just love a happy ending ;-) Graeme |
