Author |
Message |
ttc
Junior Username: ttc
Post Number: 15 Registered: 6-2009
| Posted on Friday, May 28, 2010 - 2:55 pm: | |
I have an '86 Series I long scale four string which emits very loud cracks, crunches and shrieks when the cable is brushed this way or that. To stop it you have to move the cable again or turn off the amp, or unplug and replug the cable--something to shift it around. It feels like a loose connection but everything looks OK on the back of the jack--solder seems fine. I have also tried different cables so the problem is definitely in the bass. This is the second five pin jack I have had on the bass; I replaced it years ago for the same problem. Anyone else encountered this? |
lmiwa
Advanced Member Username: lmiwa
Post Number: 306 Registered: 2-2008
| Posted on Sunday, May 30, 2010 - 5:27 pm: | |
Sounds like the jack might be moving slightly in the bass. I would check the ground connections. |
terryc
Senior Member Username: terryc
Post Number: 1211 Registered: 11-2004
| Posted on Tuesday, June 01, 2010 - 7:30 am: | |
Could be the cable itself, if it is old cable the screening & insulation may have broken down, they have a tendency to crack inside the main covering over time. You could check for continuity on each pin with a battery at one end of the cable and a meter at the other. |
artswork99
Moderator Username: artswork99
Post Number: 1148 Registered: 7-2007
| Posted on Tuesday, June 01, 2010 - 7:51 am: | |
I recently went through a similar issue with my Series. The screw that holds the 5 pin jack on the bass was slightly loose and I thought that was the problem. After tightening and further diagnostics I found it to be the cable. I stripped an inch of cable and re-soldered... the same issue. Took off another inch or more and trapped the problem. After this re-solder the problem has completely gone away. I try and keep the input jack tightened and can tell when it starts to loosen by feeling it move slightly when I remove the cable (remove the cable and touch the pins on the input jack, they will move slightly inward if loose at all - time to tighten the internal screw). |
ttc
Junior Username: ttc
Post Number: 16 Registered: 6-2009
| Posted on Wednesday, June 02, 2010 - 2:33 pm: | |
Many thanks for all this help. Artswork99, is the screw you refer to the one on the inside of the bass that holds the pin assembly to the jack housing (i.e. not the two screws holding the housing to the body of the bass)? If so, it seems to me that the way to keep the pins snug in the housing is to LOOSEN the screw so it sticks out into the hole made for it in the side of the housing. Is this wrong? Thanks again, TTC |
artswork99
Moderator Username: artswork99
Post Number: 1152 Registered: 7-2007
| Posted on Wednesday, June 02, 2010 - 2:35 pm: | |
That is correct TTC. Though it does tighten against the housing when turning in the counter-clockwise direction. (Message edited by artswork99 on June 02, 2010) |
mica
Moderator Username: mica
Post Number: 6779 Registered: 6-2000
| Posted on Wednesday, June 02, 2010 - 6:28 pm: | |
Did the crackling change when you adjusted the set screw inside the bass? |
ttc
Junior Username: ttc
Post Number: 17 Registered: 6-2009
| Posted on Monday, June 07, 2010 - 11:56 am: | |
The problem does seem to be at least partly due to the pins shifting within the housing. The pins moved slightly within the housing so I tightened the set screw as hard as I could, but simply plugging in the cord loosened the pins almost immediately, and the crackling went on as before. The cord does not seem to be the problem because it does not crackle when plugged into my other Series I. Should I try to get a new set screw? or a new pin/housing assembly? Thanks for all your help. TTC |
mica
Moderator Username: mica
Post Number: 6787 Registered: 6-2000
| Posted on Tuesday, June 08, 2010 - 11:14 am: | |
Sounds like you have the connection in the jack as an ITT Canon and the housing is Switchcraft. They almost fit together, and it does seem that the mating between them has worn. I'm not in the office today, but you can call me tomorrow to discuss some details. Do check that the 1/4" jack nut is fully tightened. It can interfere with the grounding if it is not. |
ttc
Junior Username: ttc
Post Number: 18 Registered: 6-2009
| Posted on Wednesday, June 09, 2010 - 1:33 pm: | |
Many thanks, Mica--housing is definitely Switchcraft; I will check the make of the pin assembly, which is not original to the bass. After I check that and the 1/4" jack nut I will call. Best TTC |
mica
Moderator Username: mica
Post Number: 6790 Registered: 6-2000
| Posted on Wednesday, June 09, 2010 - 1:44 pm: | |
Unless you're following the election day thread, you might not know I was only here for a couple of hours today. I'll be back again tomorrow, so please try and reach me then, or email me your phone number and I'll call you then. |
ttc
Junior Username: ttc
Post Number: 19 Registered: 6-2009
| Posted on Monday, June 14, 2010 - 1:55 pm: | |
Mica, Sorry--have not had a chance to look at the bass yet. I will call as soon as I can. Best TTC |