Author |
Message |
mica
Moderator Username: mica
Post Number: 2377 Registered: 6-2000
| Posted on Thursday, March 31, 2005 - 2:41 pm: | |
Here's how your work order 13964 reads as of now: NECK scale: 30.75 strings: 4 7-piece through body neck MAP|PH|MAP|EB|MAP|PH|MAP fingerboard: ebony with abalone inlays 1.5x2.25 (like Stanley's) side markers: Red LEDs with 2 amber each @ 12th and 24th peghead: Crown, bevelled BODY Sandwich: Coco Bolo top [wood to be selected] Maple pinstripe Purpleheart laminate Maple pinstripe Vermilion core, hollow Maple pinstripe Purpleheart laminate Maple pinstripe Coco Bolo Back shape: Small Standard, no tummy or elbow carving ROUTING: pickups: 2 FatBoy truss rod cover: 4R (standard for SC model) backplates: brass electronics: 2 volume, 2 filter, 2-3 position Q siwtches FINISH: polyester gloss with satin neck feel SETUP: logo: silver no script hardware: gold plated strap anchor: gold straplocks strings: .045-.065-.080-.105 case: hardshell Please review this list of features. Construction has not yet started, so make sure that any changes, additions, misunderstood instructions are sorted out quickly. Once the top wood is selected, Chip will start building right away. |
bsee
Senior Member Username: bsee
Post Number: 889 Registered: 3-2004
| Posted on Friday, April 29, 2005 - 10:31 am: | |
Highlighted in red are the adjustments/clarifications that came out of my phone conversation with Valentino yesterday: NECK scale: 30.75 strings: 4 7-piece through body neck MAP|PH|MAP|EB|MAP|PH|MAP fingerboard: ebony with abalone inlays 1.5x2.15 (like Stanley's) 1.5 is the nut width, 2.15 is the string spacing, center-to-center, at the bridge (approx 18mm) side markers: Red LEDs with 2 amber each @ 12th and 24th with internal dimmer pot peghead: K Crown, bevelled This is the headstock that is narrower near the neck to go with the narrow nut, right? Chip's choice on headstock sandwich to go with the rest of the woods and show off the bevel. Very dark and symmetrical peghead face to bring out the hardware and logo BODY Sandwich: Coco Bolo top [3766 approximately per my template and adjusted to Chip's preference] Maple pinstripe Purpleheart laminate Maple pinstripe Vermilion core, hollow Maple pinstripe Purpleheart laminate Maple pinstripe Coco Bolo Back [3774 with bookmatch reversed and the dark curve around the swirly area following the body contour. I'd like to see a template on this before it is cut, but I can live without it.] shape: Small Standard, no tummy or elbow carving ROUTING: pickups: 2 FatBoy truss rod cover: 4R (standard for SC model) clarification: Series pickup positioning, so the truss rod cover is small backplates: brass electronics: 2 volume, 2 filter, 2-3 position Q switches The positions of the LED switch and 1/4" jack will be reversed with the jack closer to the neck FINISH: polyester gloss with satin neck feel SETUP: logo: silver no script hardware: gold plated strap anchor: gold straplocks mounted using threaded inserts rather than screws, if possible strings: .045-.065-.080-.105 case: hardshell |
bsee
Senior Member Username: bsee
Post Number: 947 Registered: 3-2004
| Posted on Friday, September 16, 2005 - 12:10 pm: | |
Just a note to capture the results of a phone conversation that Mica and I had yesterday: 1. The pickup positioning and truss rod cover will be as per Stanley's 30th anniversary bass. This corresponds to the positioning of older Series instruments, not the current standards. 2. We will go with the .040-.060-.080-.100 long scale string set. 3. There will be a stop order to discuss the custom inlay at the appropriate time if we haven't nailed it sooner. -Bob |
flaxattack
Senior Member Username: flaxattack
Post Number: 598 Registered: 4-2004
| Posted on Saturday, September 17, 2005 - 9:20 am: | |
isnt this the same bob who said there were no changes after he placed the order>? |
|