Series I Electronics Without the Box? Log Out | Topics | Search
Moderators | Register | Edit Profile

Alembic Club » Alembic Basses & Guitars » Archive: 2007 » Archive through November 26, 2007 » Series I Electronics Without the Box? « Previous Next »

Author Message
ampeglb100
Intermediate Member
Username: ampeglb100

Post Number: 123
Registered: 11-2004
Posted on Friday, October 26, 2007 - 9:24 am:   Edit Post

Hello-

So I see a few Series I loaded basses around lately (Bass NW and The Low End) that have no "box" and are supposedly wired such that you don't need anything extra to operate them... meaning you can simply plug in with the 1/4" input and have the full Series I electronics available. Sorry if I am mis-speaking or now using the correct terminaology here. Is this wiring a standard, factory configuration? If so, do you lose anything vs. the "normal" Series I wiring? Any help would be great.

Thanks,

Andy
precarius
Advanced Member
Username: precarius

Post Number: 242
Registered: 11-2005
Posted on Friday, October 26, 2007 - 9:35 am:   Edit Post

Andy- Here's a FAQ thread with a PDF file telling you how to wire a stereo bass to mono or you can make a stereo (TRS) to mono cord.
http://alembic.com/club/messages/16271/29811.html?1152754164
Mike
Beware that the two 9 volt batteries only equal about 40 hours of plugged in time.

(Message edited by Precarius on October 26, 2007)
olieoliver
Senior Member
Username: olieoliver

Post Number: 1597
Registered: 2-2006
Posted on Friday, October 26, 2007 - 9:44 am:   Edit Post

I have a Series 2 that I play often without the power supply. I have a special cord like the one Mike mentioned above and the bass works on the batteries.
In fact I am going in the studio tomorrow and plan on using it without th "box".

Olie

(Message edited by olieoliver on October 26, 2007)
hieronymous
Advanced Member
Username: hieronymous

Post Number: 226
Registered: 1-2005
Posted on Friday, October 26, 2007 - 1:23 pm:   Edit Post

A Rickenbacker "Rick-o-Sound" box works too, but they're no longer in production.
dfung60
Advanced Member
Username: dfung60

Post Number: 280
Registered: 5-2002
Posted on Saturday, October 27, 2007 - 10:14 pm:   Edit Post

The stock wiring on an older (probably pre-1987 or so) Series bass is set up with stereo output on both the 1/4" jack and on the 5-pin Cannon connector. The audio outputs on both connectors are exactly the same. Three of the five Cannon pins are the two pickup audio hots and a common ground. The other two pins are the external power supply which I seem to remember is around 30VDC.

When you stick a plug in the 1/4" jack it turns off the external power and switches on the two 9V internal batteries. The Series electronics are optimized for performance, not low power, so a set of batteries will last only 10s of hours instead of the hundreds or even thousands of hours you see with EMGs and other active pickups.

All that's in the floor or rack box is an AC->DC power supply and a simple switching system so you can get the individual pickup signals or a mono blend of the two.

On later Series basses, the 1/4" jack is a mono out. It still does all the switching of power supply, but you can't get the individual pickup outputs there, only on the Cannon connector. This is generally a good change I think - in the original configuration, a regular guitar cord will give you only the output of one pickup which means you'll need an adapter to use the bass with a wireless transmitter and you're also hosed if you don't have your special cables in general. When you have a new instrument built, it looks like you can pick "old" or "new" style and even the option of having a stereo/mono switch on the 1/4" jack.

The outputs on the 5-pin connector are unbalanced signals, just like you'd find on the 1/4" jack. Even though the Cannon connector is used, they're not balanced, so you're not missing out on anything there. The output on both 1/4 and Cannon are low-impedance since everything going through active buffering amps in the in the internal electronics.

So, you're not losing out on anything soundwise without the external power supply box, but you should make an adjustment on what you pay for an instrument that's missing this stuff. If you want a replacement box and cable that must cost between $600-1000 from Alembic, not a small amount!

David Fung
ampeglb100
Intermediate Member
Username: ampeglb100

Post Number: 124
Registered: 11-2004
Posted on Sunday, October 28, 2007 - 7:04 am:   Edit Post

Very good - thanks everyone for the clarification.

Andy

Topics | Last Day | Last Week | Tree View | Search | Help/Instructions | Program Credits Administration